Firmware 2.62Beta8 is ready to download.

In this release:

Added total flight time (sum from all flights) in post flight statistics page. For FC this is time when FC is armed, for single OSD and Pitlab AP this is time from system start (or last store base before takeoff) till landing.

Battery capacity/cutoff is readed from FC (pixhawk/APM) at startup, reflecting last FC settings made by GCS. And selecting battery from OSD menu sets new capacity/cutoff  to the FC.

In FPV_manager (page OSD ->settings) added options for reset/update odometer and total flight time.  Important for those who transfer OSD/AP to another airplane.

Firmware 2.62beta7 is ready.

In this release fixed bug in airspeed compensation with altitude/static pressure change.

2.62beta6 is ready!

In this release some minor bugs removed, e.g.  in auto post flight info and odometer calculations.

In ground station added new option for automatic baud rate scan/discovery for Bluetooth module

New 2.62Beta5 is ready, with new ACRO mode (OSD+Autopilot).

New ACRO options include:

-pitch  and roll rate (degree/second)
-mode switch configuration for 3 or 4 position RC switch.

Additionally Autopilot manu is re-arranged  to fit ACRO mode settings (RTH/AUTO options are moved  into AUTO flight submenu  in Autopilot menu

In this Beta4 release:

1. Added OSD MavLink telemetry output on UART1 port (buddy flight port).  Option activated in OSD menu -> service -> UART1 ->mavlink. These messages are available on USART pport: HEARTBEAT (required by MavLink protocol)
   SYS_STATUS (battery voltage/current/mAh, discharge percentage, autopilot sensor status/errors)
   VFR_HUD (airspeed, heading, throttle, altitude, variometer)
   GPS_RAW_INT (GPS position, altitude, course, speed over ground, sat
   Note: Baud speed for mavlink output can be set  in OSD menu->service->UART1.
2. Proper DO_JUMP  command handling  when selected from OSD menu->mission  allows now to split large mission into several sub-missions with easy selection from menu.
3. Fixed bug in barometric altitude settings: OSD ignored barometric altitude from Pitlab Autopilot and presented GPS altitude instead.

After fighting with some bugs in Mavllink2 protocol,  new firmware 262beta3 is available.

Bug was discovered in OSD->Pitlab Autopilot  data interchange (it may affect STAB/AUTO mode), but may occur also in OSD->Pixhawk  cooperation and result in wrong data received by OSD.

Beta2 of mavLink enabled firmware is ready.

Changes:

-Added menu for FC PID tuning (Basic)

-Added menu for FC Fence management

-Fixed RSSI bug when working with Pitlab Autopilot.

-Fixed bug in RC monitor settings imported from previous OSD version (2.60).

Note: RC monitor settings changed in  layout designer in FPV_manager Beta1  need to be  fixed/corrected  in FPV_manager Beta2  to work properly!

We are proud to announce new MavLink-enabled 2.62 firmware.

This firmware is dedicated for present OSD/AP/GS users as well as for pilots using third party flight controllers with MavLink  protocol (e.g. APM or Pixhawk) who are looking for professional,  functional and easy to use OSD for their airplanes or multirotors.

Our OSD integrates seamlessly with these controllers, presenting navigation information from controller, and also providiong some functionalities  from GCS (ground control station), in most cases allowing to fly copters and execute missions without  laptop and live connection to GCS.

First BETA version is available now (link to current version is in menu at left side of this page).

Note: Version 2.62  only with OSD board (PCB) version 2.2 or later.

New firmware 2.60 is ready!

After many months of work and test new official release 2.60 is ready.

Many thanks to all users participating in beta-tests, your feedback makes this version even more stable and reliable.

This version is available for free for all users, and will work with all hardware version, even first BETA boards. But this v2.60 is the last version working with all boards.

Link to download is available on official pitlab website (english version: https://www.pitlab.com/fpv-system/download.html, polish version: http://www.pitlab.pl/system-fpv/do-pobrania.html), or in download menu on the left side of this page.

We wish you many safe flights with our system!

New firmware 2.52rc3 is ready to download and test.

There is only one bug fixed in autopilot’s diversity functionality in CPPM1/CPPM6 mode.  All single RC input modes and diversity modes with SBUS were not affected by this bug.

Link for download is in the Download menu on the left side of this page.